P2714 — Pressure Control Solenoid "D" Performance/Stuck Off

OBD2 code P2714 flags a problem with the automatic transmission control (pressure control solenoid "D" performance/stuck off). Short, gentle driving to a shop is usually possible. Common culprits: internal mechanical wear (clutches, torque converter), low or degraded transmission fluid, valve body wear.

powertrain (engine/transmission)

Is it safe to drive?

Drive with caution Drive only if the transmission still shifts predictably, and avoid highway speeds. Driving with slipping or limp mode accelerates internal wear — every kilometre can add to the final repair bill.

How to diagnose with an OBD scanner

Read the code and freeze frame Connect an OBD2 scanner, confirm P2714 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the automatic transmission control for damage, corrosion, chafing or poor contact.
Subsystem check Command the pressure control solenoid "D" performance/ on and off with a scanner and watch the feedback signal; then remove and inspect the mechanism for sticking before replacing it.
Subsystem check Check transmission fluid level and condition — dark, burnt fluid points to internal wear.
Subsystem check Read transmission-specific codes and live data (solenoid states, input/output speed) with a capable scanner.
Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P2714 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for P2714 (parts and labor, USD, independent shop rates): Transmission rebuild or replacement: $2,500–$5,500; Valve body repair or replacement: $700–$1,500; Transmission fluid service: $150–$350; Replace a shift solenoid: $300–$800. Overall, fixing P2714 usually costs between $150 and $5,500. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

How do I diagnose P2714 myself?

Start with a scan: confirm P2714, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the pressure control solenoid "D" performance/, and verify the suspect component against live data before buying parts.

What are the symptoms of P2714?

Drivers most often notice: no movement in severe cases, Check Engine or transmission warning light on, transmission stuck in one gear (limp mode), shuddering at highway speed.

What does OBD2 code P2714 mean?

Is it safe to drive with P2714?

Drive only if the transmission still shifts predictably, and avoid highway speeds. Driving with slipping or limp mode accelerates internal wear — every kilometre can add to the final repair bill.

Will P2714 clear itself?

Sometimes P2714 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

What does P2714 mean?

Behind P2714 is a specific failure in the automatic transmission control: pressure control solenoid "D" performance/stuck off. The onboard computer stores it in the powertrain (engine/transmission) group after verifying the fault over repeated checks.

“Stuck” means the pressure control solenoid "D" performance/ is commanded to change state but feedback shows it does not move — or moves when it should not. Typical physical reasons are carbon or dirt jamming the mechanism, welded relay contacts, or a weak actuator.

This code does not appear from a single bad reading: the module must see the fault condition repeat under defined operating conditions before it turns on the warning light. The freeze frame captured with P2714 — engine load, rpm, temperature, speed — tells you exactly when the problem occurs, so reproduce those conditions when testing.

What causes P2714?

mechanism of the pressure control solenoid "D" performance/ jammed by carbon, dirt or corrosion
weak actuator motor or broken spring
welded relay contacts keeping the circuit permanently on
faulty transmission speed sensor
low or degraded transmission fluid
valve body wear
wiring or connector faults in the valve body harness

Common symptoms of P2714

no movement in severe cases
Check Engine or transmission warning light on
transmission stuck in one gear (limp mode)
shuddering at highway speed
slipping between gears
harsh or delayed shifting

How to diagnose P2714

Connect an OBD2 scanner, confirm P2714 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
Visually inspect the wiring harness and connectors related to the automatic transmission control for damage, corrosion, chafing or poor contact.
Command the pressure control solenoid "D" performance/ on and off with a scanner and watch the feedback signal; then remove and inspect the mechanism for sticking before replacing it.
Check transmission fluid level and condition — dark, burnt fluid points to internal wear.
Read transmission-specific codes and live data (solenoid states, input/output speed) with a capable scanner.
Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P2714 does not return.

How to fix P2714

Start with the cheapest and most common causes before replacing expensive parts:

Transmission rebuild or replacement — $2,500–$5,500
Valve body repair or replacement — $700–$1,500
Transmission fluid service — $150–$350
Replace a shift solenoid — $300–$800

How much does it cost to fix P2714?

Repair cost depends on which component actually failed. Typical scenarios for P2714 (parts and labor, USD, independent shop rates):

Transmission rebuild or replacement: $2,500–$5,500
Valve body repair or replacement: $700–$1,500
Transmission fluid service: $150–$350
Replace a shift solenoid: $300–$800

Overall, fixing P2714 usually costs between $150 and $5,500. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P2714?