P2464 — Diesel Particulate Filter Differential Pressure Too Low Bank 2

OBD2 code P2464 flags a problem with the diesel particulate filter (DPF) (diesel particulate filter differential pressure too low bank 2). Short, gentle driving to a shop is usually possible. Common culprits: excessive ash loading (end of DPF life), failed regeneration due to sensor or wiring faults, faulty differential pressure or exhaust temperature sensor.

powertrain (engine/transmission)

Is it safe to drive?

Drive with caution Drive only enough to reach a service. A saturated DPF pushes the car into limp mode, and continued driving with failed regenerations dilutes engine oil with fuel — that damages the engine itself.

How to diagnose with an OBD scanner

  1. Read the code and freeze frame Connect an OBD2 scanner, confirm P2464 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the diesel particulate filter (DPF) for damage, corrosion, chafing or poor contact.
  4. Subsystem check Read DPF soot load and differential pressure in live data before and after a forced regeneration.
  5. Subsystem check Verify exhaust temperature and pressure sensor readings are plausible at idle and under load.
  6. Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P2464 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for P2464 (parts and labor, USD, independent shop rates): Replace a pressure or temperature sensor: $150–$450; DPF replacement: $1,500–$4,000; Forced regeneration / cleaning: $150–$400. Overall, fixing P2464 usually costs between $150 and $4,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

What does OBD2 code P2464 mean?

OBD2 code P2464 flags a problem with the diesel particulate filter (DPF) (diesel particulate filter differential pressure too low bank 2). Short, gentle driving to a shop is usually possible. Common culprits: excessive ash loading (end of DPF life), failed regeneration due to sensor or wiring faults, faulty differential pressure or exhaust temperature sensor.

How much does it cost to fix P2464?

Replace a pressure or temperature sensor — $150–$450; DPF replacement — $1,500–$4,000; Forced regeneration / cleaning — $150–$400. Exact cost depends on the root cause, your vehicle and local labor rates — a proper diagnosis is the cheapest first step.

Is it safe to drive with P2464?

Drive only enough to reach a service. A saturated DPF pushes the car into limp mode, and continued driving with failed regenerations dilutes engine oil with fuel — that damages the engine itself.

How do I diagnose P2464 myself?

Start with a scan: confirm P2464, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the diesel particulate filter (DPF), and verify the suspect component against live data before buying parts.

Will P2464 clear itself?

Sometimes P2464 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

What does P2464 mean?

The engine control module sets P2464 when it detects a fault in the diesel particulate filter (DPF). In practical terms: diesel particulate filter differential pressure too low bank 2. The code belongs to the powertrain (engine/transmission) group of OBD2 codes.

“Bank 2” means the side of the engine opposite to cylinder 1. Verify which side that is on your specific engine before testing or replacing parts.

The module monitors this system continuously while driving. When readings fall outside the expected range for a defined number of drive cycles, it stores P2464 and switches on the warning light. Freeze frame data saved with the code shows the exact conditions — rpm, load, temperature, speed — at the moment the fault was detected, which is the best starting point for diagnosis.

Common symptoms of P2464

  • Check Engine or DPF warning light on
  • frequent regeneration attempts
  • rising oil level from fuel dilution
  • increased fuel consumption
  • loss of power and limp mode

What causes P2464?

  • excessive ash loading (end of DPF life)
  • engine faults producing excess soot (EGR, injectors)
  • soot-overloaded DPF from short-trip driving
  • faulty differential pressure or exhaust temperature sensor

How to diagnose P2464

  1. Connect an OBD2 scanner, confirm P2464 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Visually inspect the wiring harness and connectors related to the diesel particulate filter (DPF) for damage, corrosion, chafing or poor contact.
  4. Read DPF soot load and differential pressure in live data before and after a forced regeneration.
  5. Verify exhaust temperature and pressure sensor readings are plausible at idle and under load.
  6. Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P2464 does not return.

How to fix P2464

Start with the cheapest and most common causes before replacing expensive parts:

  • Replace a pressure or temperature sensor — $150–$450
  • DPF replacement — $1,500–$4,000
  • Forced regeneration / cleaning — $150–$400

How much does it cost to fix P2464?

Repair cost depends on which component actually failed. Typical scenarios for P2464 (parts and labor, USD, independent shop rates):

  • Replace a pressure or temperature sensor: $150–$450
  • DPF replacement: $1,500–$4,000
  • Forced regeneration / cleaning: $150–$400

Overall, fixing P2464 usually costs between $150 and $4,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P2464?

Drive only enough to reach a service. A saturated DPF pushes the car into limp mode, and continued driving with failed regenerations dilutes engine oil with fuel — that damages the engine itself.

Related OBD2 codes