P2460 — Diesel Particulate Filter Pressure Sensor "B" Circuit Low

What are the symptoms of P2460?

Drivers most often notice: loss of power and limp mode, Check Engine or DPF warning light on, rising oil level from fuel dilution, frequent regeneration attempts.

What does OBD2 code P2460 mean?

OBD2 code P2460 flags a problem with the diesel particulate filter (DPF) (diesel particulate filter pressure sensor "B" circuit low). Short, gentle driving to a shop is usually possible. Common culprits: faulty differential pressure or exhaust temperature sensor, failed regeneration due to sensor or wiring faults, soot-overloaded DPF from short-trip driving.

How much does it cost to fix P2460?

Forced regeneration / cleaning — $150–$400; DPF replacement — $1,500–$4,000; Replace a pressure or temperature sensor — $150–$450. Exact cost depends on the root cause, your vehicle and local labor rates — a proper diagnosis is the cheapest first step.

Will P2460 clear itself?

Sometimes P2460 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

Is it safe to drive with P2460?

Drive only enough to reach a service. A saturated DPF pushes the car into limp mode, and continued driving with failed regenerations dilutes engine oil with fuel — that damages the engine itself.

What does P2460 mean?

P2460 is logged by the onboard diagnostics when the diesel particulate filter (DPF) does not behave as expected. The official definition is “Diesel Particulate Filter Pressure Sensor "B" Circuit Low”. This is a powertrain (engine/transmission) category code.

“Circuit low” means the voltage on the diesel particulate filter pressure sensor "B" circuit stays below the expected minimum — close to ground. The usual physical reasons are a short to ground, a chafed wire touching metal, a missing supply voltage, or a failed component dragging the signal down.

The module monitors this system continuously while driving. When readings fall outside the expected range for a defined number of drive cycles, it stores P2460 and switches on the warning light. Freeze frame data saved with the code shows the exact conditions — rpm, load, temperature, speed — at the moment the fault was detected, which is the best starting point for diagnosis.

What causes P2460?

• failed diesel particulate filter pressure sensor "B" pulling the signal low
• signal wire shorted to ground (chafed insulation)
• missing supply voltage to the diesel particulate filter pressure sensor "B"
• faulty differential pressure or exhaust temperature sensor
• soot-overloaded DPF from short-trip driving
• engine faults producing excess soot (EGR, injectors)
• excessive ash loading (end of DPF life)

Common symptoms of P2460

• loss of power and limp mode
• Check Engine or DPF warning light on
• rising oil level from fuel dilution
• frequent regeneration attempts
• increased fuel consumption

How to diagnose P2460

1. Connect an OBD2 scanner, confirm P2460 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
2. Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
3. Visually inspect the wiring harness and connectors related to the diesel particulate filter (DPF) for damage, corrosion, chafing or poor contact.
4. Check for supply voltage at the diesel particulate filter pressure sensor "B" connector first; then measure resistance from the signal wire to ground — near-zero ohms confirms a short to ground in the harness.
5. Read DPF soot load and differential pressure in live data before and after a forced regeneration.
6. Verify exhaust temperature and pressure sensor readings are plausible at idle and under load.
7. Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P2460 does not return.

How to fix P2460

Start with the cheapest and most common causes before replacing expensive parts:

• Forced regeneration / cleaning — $150–$400
• DPF replacement — $1,500–$4,000
• Replace a pressure or temperature sensor — $150–$450

How much does it cost to fix P2460?

Repair cost depends on which component actually failed. Typical scenarios for P2460 (parts and labor, USD, independent shop rates):

• Forced regeneration / cleaning: $150–$400
• DPF replacement: $1,500–$4,000
• Replace a pressure or temperature sensor: $150–$450

Overall, fixing P2460 usually costs between $150 and $4,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P2460?

Drive only enough to reach a service. A saturated DPF pushes the car into limp mode, and continued driving with failed regenerations dilutes engine oil with fuel — that damages the engine itself.

Related OBD2 codes

• P2400: Evaporative Emission System Leak Detection Pump Control Circuit/Open
• P2401: Evaporative Emission System Leak Detection Pump Control Circuit Low
• P2402: Evaporative Emission System Leak Detection Pump Control Circuit High
• P2403: Evaporative Emission System Leak Detection Pump Sense Circuit/Open
• P2404: Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance
• P2405: Evaporative Emission System Leak Detection Pump Sense Circuit Low