U1037 — SCP (J1850) Invalid or Missing Data for Wheels

vehicle network

Is it safe to drive?

Drive with caution Depends on what is affected. A single dead convenience module is fine to drive with; loss of communication with engine, braking or steering modules is not. If multiple critical systems drop out, do not drive.

How to diagnose with an OBD scanner

  1. Read the code and freeze frame Connect an OBD2 scanner, confirm U1037 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many U0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the vehicle network (CAN bus) communication for damage, corrosion, chafing or poor contact.
  4. Subsystem check Measure resistance between CAN-High and CAN-Low at the OBD port with power off — about 60 Ω is healthy.
  5. Subsystem check Scan all modules: the one that does not respond is either the culprit or downstream of the break.
  6. Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm U1037 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for U1037 (parts and labor, USD, independent shop rates): Repair CAN wiring or connectors: $100–$400; Remove interfering aftermarket device: $0–$150; Replace the faulty control module: $300–$1,500. Overall, fixing U1037 usually costs between $0 and $1,500. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

How much does it cost to fix U1037?

Repair CAN wiring or connectors — $100–$400; Remove interfering aftermarket device — $0–$150; Replace the faulty control module — $300–$1,500. Exact cost depends on the root cause, your vehicle and local labor rates — a proper diagnosis is the cheapest first step.

How do I diagnose U1037 myself?

Start with a scan: confirm U1037, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the vehicle network (CAN bus) communication, and verify the suspect component against live data before buying parts.

What does OBD2 code U1037 mean?

SCP (J1850) Invalid or Missing Data for Wheels (U1037): a vehicle network fault affecting the vehicle network (CAN bus) communication. Short, gentle driving to a shop is usually possible. Most often caused by poor grounds or low battery voltage, aftermarket equipment interfering with the bus, damaged CAN bus wiring or short to power/ground.

Will U1037 clear itself?

Sometimes U1037 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

What is the most common cause of U1037?

The most common causes are: poor grounds or low battery voltage, aftermarket equipment interfering with the bus, damaged CAN bus wiring or short to power/ground.

What does U1037 mean?

U1037 (SCP (J1850) Invalid or Missing Data for Wheels) is stored when self-diagnostics detect abnormal readings or behaviour of the vehicle network (CAN bus) communication. It belongs to the vehicle network category.

This code does not appear from a single bad reading: the module must see the fault condition repeat under defined operating conditions before it turns on the warning light. The freeze frame captured with U1037 — engine load, rpm, temperature, speed — tells you exactly when the problem occurs, so reproduce those conditions when testing.

What causes U1037?

  • damaged CAN bus wiring or short to power/ground
  • corroded connectors, especially in wet areas
  • poor grounds or low battery voltage
  • a faulty module pulling the bus down
  • aftermarket equipment interfering with the bus
  • water ingress in harness junctions

Common symptoms of U1037

  • modules intermittently not communicating with the scanner
  • random, hard-to-reproduce electrical glitches
  • multiple warning lights on at once
  • intermittent loss of functions (gauges, windows, steering assist)
  • no-start or intermittent starting in some cases

How to diagnose U1037

  1. Connect an OBD2 scanner, confirm U1037 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many U0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Visually inspect the wiring harness and connectors related to the vehicle network (CAN bus) communication for damage, corrosion, chafing or poor contact.
  4. Measure resistance between CAN-High and CAN-Low at the OBD port with power off — about 60 Ω is healthy.
  5. Scan all modules: the one that does not respond is either the culprit or downstream of the break.
  6. Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm U1037 does not return.

How to fix U1037

Start with the cheapest and most common causes before replacing expensive parts:

  • Repair CAN wiring or connectors — $100–$400
  • Remove interfering aftermarket device — $0–$150
  • Replace the faulty control module — $300–$1,500

How much does it cost to fix U1037?

Repair cost depends on which component actually failed. Typical scenarios for U1037 (parts and labor, USD, independent shop rates):

  • Repair CAN wiring or connectors: $100–$400
  • Remove interfering aftermarket device: $0–$150
  • Replace the faulty control module: $300–$1,500

Overall, fixing U1037 usually costs between $0 and $1,500. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with U1037?

Depends on what is affected. A single dead convenience module is fine to drive with; loss of communication with engine, braking or steering modules is not. If multiple critical systems drop out, do not drive.

Related OBD2 codes