P3455 — Cylinder 7 Exhaust Valve Control Circuit Low

OBD2 code P3455 flags a problem with the sensor and actuator circuits (cylinder 7 exhaust valve control circuit low). The car is usually drivable while you plan the repair. Common culprits: corroded, loose or damaged connector, faulty sensor or actuator of the affected circuit, blown fuse feeding the circuit.

For Ford vehicles

cylinder 7 exhaust valve control circuit – signal too low

powertrain (engine/transmission)

Is it safe to drive?

Short-term driving is OK In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

How to diagnose with an OBD scanner

Read the code and freeze frame Connect an OBD2 scanner, confirm P3455 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the cylinder 7 exhaust valve control for damage, corrosion, chafing or poor contact.
Subsystem check Check for supply voltage at the cylinder 7 exhaust valve control connector first; then measure resistance from the signal wire to ground — near-zero ohms confirms a short to ground in the harness.
Subsystem check Measure reference voltage, ground and signal continuity at the component connector.
Subsystem check Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P3455 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for P3455 (parts and labor, USD, independent shop rates): Replace the faulty sensor or actuator: $150–$500; Control module repair: $300–$1,000; Repair wiring or connectors: $80–$250. Overall, fixing P3455 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

What is the most common cause of P3455?

The most common causes are: corroded, loose or damaged connector, faulty sensor or actuator of the affected circuit, blown fuse feeding the circuit.

What are the symptoms of P3455?

Drivers most often notice: possible limp mode depending on the affected component, the affected system operates intermittently or not at all, increased fuel consumption in some cases, Check Engine Light on.

What does OBD2 code P3455 mean?

How do I diagnose P3455 myself?

Start with a scan: confirm P3455, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the cylinder 7 exhaust valve control, and verify the suspect component against live data before buying parts.

Will P3455 clear itself?

Sometimes P3455 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

What does P3455 mean?

The engine control module sets P3455 when it detects a fault in the sensor and actuator circuits. In practical terms: cylinder 7 exhaust valve control circuit low. The code belongs to the powertrain (engine/transmission) group of OBD2 codes.

P3455 refers specifically to cylinder 7. On inline engines cylinders are counted from the front (belt end); on V-engines the numbering depends on the manufacturer, so check the firing-order diagram for your exact model. Location matters for the repair bill: some cylinders require intake manifold removal, which adds labor time.

“Circuit low” means the voltage on the cylinder 7 exhaust valve control circuit stays below the expected minimum — close to ground. The usual physical reasons are a short to ground, a chafed wire touching metal, a missing supply voltage, or a failed component dragging the signal down.

The module monitors this system continuously while driving. When readings fall outside the expected range for a defined number of drive cycles, it stores P3455 and switches on the warning light. Freeze frame data saved with the code shows the exact conditions — rpm, load, temperature, speed — at the moment the fault was detected, which is the best starting point for diagnosis.

What causes P3455?

failed cylinder 7 exhaust valve control pulling the signal low
missing supply voltage to the cylinder 7 exhaust valve control
signal wire shorted to ground (chafed insulation)
control module driver fault
poor ground connection
faulty sensor or actuator of the affected circuit
blown fuse feeding the circuit

Common symptoms of P3455

possible limp mode depending on the affected component
the affected system operates intermittently or not at all
increased fuel consumption in some cases
Check Engine Light on

How to diagnose P3455

Connect an OBD2 scanner, confirm P3455 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
Visually inspect the wiring harness and connectors related to the cylinder 7 exhaust valve control for damage, corrosion, chafing or poor contact.
Check for supply voltage at the cylinder 7 exhaust valve control connector first; then measure resistance from the signal wire to ground — near-zero ohms confirms a short to ground in the harness.
Measure reference voltage, ground and signal continuity at the component connector.
Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P3455 does not return.

How to fix P3455

Start with the cheapest and most common causes before replacing expensive parts:

Replace the faulty sensor or actuator — $150–$500
Control module repair — $300–$1,000
Repair wiring or connectors — $80–$250

How much does it cost to fix P3455?

Repair cost depends on which component actually failed. Typical scenarios for P3455 (parts and labor, USD, independent shop rates):

Replace the faulty sensor or actuator: $150–$500
Control module repair: $300–$1,000
Repair wiring or connectors: $80–$250

Overall, fixing P3455 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P3455?

In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.