P3415 — Cylinder 2 Exhaust Valve Control Circuit Low

P3415 — Cylinder 2 Exhaust Valve Control Circuit Low. A fault in the sensor and actuator circuits. The car is usually drivable while you plan the repair. Typical causes: open or shorted wiring in the circuit, blown fuse feeding the circuit, poor ground connection.

For Ford vehicles

cylinder 2 exhaust valve control circuit – signal too low

powertrain (engine/transmission)

Is it safe to drive?

Short-term driving is OK In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

How to diagnose with an OBD scanner

  1. Read the code and freeze frame Connect an OBD2 scanner, confirm P3415 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the cylinder 2 exhaust valve control for damage, corrosion, chafing or poor contact.
  4. Subsystem check Check for supply voltage at the cylinder 2 exhaust valve control connector first; then measure resistance from the signal wire to ground — near-zero ohms confirms a short to ground in the harness.
  5. Subsystem check Measure reference voltage, ground and signal continuity at the component connector.
  6. Subsystem check Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
  7. Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P3415 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for P3415 (parts and labor, USD, independent shop rates): Repair wiring or connectors: $80–$250; Replace the faulty sensor or actuator: $150–$500; Control module repair: $300–$1,000. Overall, fixing P3415 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

How much does it cost to fix P3415?

Repair wiring or connectors — $80–$250; Replace the faulty sensor or actuator — $150–$500; Control module repair — $300–$1,000. Exact cost depends on the root cause, your vehicle and local labor rates — a proper diagnosis is the cheapest first step.

Will P3415 clear itself?

Sometimes P3415 clears after a few drive cycles if the fault was intermittent — for example a loose connector or a tank of bad fuel. The underlying cause usually remains, so the code tends to return. Clear it once; if it comes back, diagnose rather than erase it repeatedly.

What does OBD2 code P3415 mean?

P3415 — Cylinder 2 Exhaust Valve Control Circuit Low. A fault in the sensor and actuator circuits. The car is usually drivable while you plan the repair. Typical causes: open or shorted wiring in the circuit, blown fuse feeding the circuit, poor ground connection.

How do I diagnose P3415 myself?

Start with a scan: confirm P3415, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the cylinder 2 exhaust valve control, and verify the suspect component against live data before buying parts.

Is it safe to drive with P3415?

In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

What does P3415 mean?

When P3415 appears on a scan, it means the control module has flagged a problem in the sensor and actuator circuits: cylinder 2 exhaust valve control circuit low. The fault sits in the powertrain (engine/transmission) group of the OBD2 standard.

P3415 refers specifically to cylinder 2. On inline engines cylinders are counted from the front (belt end); on V-engines the numbering depends on the manufacturer, so check the firing-order diagram for your exact model. Location matters for the repair bill: some cylinders require intake manifold removal, which adds labor time.

“Circuit low” means the voltage on the cylinder 2 exhaust valve control circuit stays below the expected minimum — close to ground. The usual physical reasons are a short to ground, a chafed wire touching metal, a missing supply voltage, or a failed component dragging the signal down.

The module monitors this system continuously while driving. When readings fall outside the expected range for a defined number of drive cycles, it stores P3415 and switches on the warning light. Freeze frame data saved with the code shows the exact conditions — rpm, load, temperature, speed — at the moment the fault was detected, which is the best starting point for diagnosis.

Common symptoms of P3415

  • Check Engine Light on
  • possible limp mode depending on the affected component
  • increased fuel consumption in some cases
  • the affected system operates intermittently or not at all

What causes P3415?

  • signal wire shorted to ground (chafed insulation)
  • missing supply voltage to the cylinder 2 exhaust valve control
  • failed cylinder 2 exhaust valve control pulling the signal low
  • faulty sensor or actuator of the affected circuit
  • open or shorted wiring in the circuit
  • control module driver fault
  • blown fuse feeding the circuit

How to diagnose P3415

  1. Connect an OBD2 scanner, confirm P3415 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Visually inspect the wiring harness and connectors related to the cylinder 2 exhaust valve control for damage, corrosion, chafing or poor contact.
  4. Check for supply voltage at the cylinder 2 exhaust valve control connector first; then measure resistance from the signal wire to ground — near-zero ohms confirms a short to ground in the harness.
  5. Measure reference voltage, ground and signal continuity at the component connector.
  6. Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
  7. Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P3415 does not return.

How to fix P3415

Start with the cheapest and most common causes before replacing expensive parts:

  • Repair wiring or connectors — $80–$250
  • Replace the faulty sensor or actuator — $150–$500
  • Control module repair — $300–$1,000

How much does it cost to fix P3415?

Repair cost depends on which component actually failed. Typical scenarios for P3415 (parts and labor, USD, independent shop rates):

  • Repair wiring or connectors: $80–$250
  • Replace the faulty sensor or actuator: $150–$500
  • Control module repair: $300–$1,000

Overall, fixing P3415 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P3415?

In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

Related OBD2 codes