P20E5 — Exhaust Gas Temperature Sensor 1/2 Correlation Bank 2

P20E5 — Exhaust Gas Temperature Sensor 1/2 Correlation Bank 2. A fault in the sensor and actuator circuits. The car is usually drivable while you plan the repair. Typical causes: faulty sensor or actuator of the affected circuit, corroded, loose or damaged connector, poor ground connection.

powertrain (engine/transmission)

Is it safe to drive?

Short-term driving is OK In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

How to diagnose with an OBD scanner

  1. Read the code and freeze frame Connect an OBD2 scanner, confirm P20E5 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Check for companion codes and TSBs Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Inspect wiring and connectors Visually inspect the wiring harness and connectors related to the exhaust gas temperature sensor 1/2 correlation bank 2 for damage, corrosion, chafing or poor contact.
  4. Subsystem check Measure reference voltage, ground and signal continuity at the component connector.
  5. Subsystem check Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
  6. Verify the repair Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P20E5 does not return.

Approximate repair cost

Repair cost depends on which component actually failed. Typical scenarios for P20E5 (parts and labor, USD, independent shop rates): Repair wiring or connectors: $80–$250; Replace the faulty sensor or actuator: $150–$500; Control module repair: $300–$1,000. Overall, fixing P20E5 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Common questions

How do I diagnose P20E5 myself?

Start with a scan: confirm P20E5, save the freeze frame and note any companion codes. Then inspect the wiring and connectors related to the sensor and actuator circuits, and verify the suspect component against live data before buying parts.

Is it safe to drive with P20E5?

In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

What are the symptoms of P20E5?

Drivers most often notice: the affected system operates intermittently or not at all, Check Engine Light on, possible limp mode depending on the affected component, increased fuel consumption in some cases.

How much does it cost to fix P20E5?

Repair wiring or connectors — $80–$250; Replace the faulty sensor or actuator — $150–$500; Control module repair — $300–$1,000. Exact cost depends on the root cause, your vehicle and local labor rates — a proper diagnosis is the cheapest first step.

What is the most common cause of P20E5?

The most common causes are: faulty sensor or actuator of the affected circuit, corroded, loose or damaged connector, poor ground connection.

What does P20E5 mean?

P20E5 (Exhaust Gas Temperature Sensor 1/2 Correlation Bank 2) is stored when self-diagnostics detect abnormal readings or behaviour of the sensor and actuator circuits. It belongs to the powertrain (engine/transmission) category.

In this definition, “Bank 2” is the side of the engine opposite to cylinder 1 and “Sensor 1” is the upstream (before the catalytic converter) sensor. Mixing up banks and sensor positions is the most common DIY mistake with this code — verify the physical location before replacing anything.

This code does not appear from a single bad reading: the module must see the fault condition repeat under defined operating conditions before it turns on the warning light. The freeze frame captured with P20E5 — engine load, rpm, temperature, speed — tells you exactly when the problem occurs, so reproduce those conditions when testing.

Common symptoms of P20E5

  • the affected system operates intermittently or not at all
  • Check Engine Light on
  • possible limp mode depending on the affected component
  • increased fuel consumption in some cases

What causes P20E5?

  • open or shorted wiring in the circuit
  • control module driver fault
  • corroded, loose or damaged connector
  • poor ground connection
  • blown fuse feeding the circuit
  • faulty sensor or actuator of the affected circuit

How to diagnose P20E5

  1. Connect an OBD2 scanner, confirm P20E5 is stored, and save the freeze frame data — it shows engine conditions when the fault was detected.
  2. Related codes often reveal the real root cause. Also check manufacturer technical service bulletins (TSB) for your make and model — many P0xxx issues have factory fixes or software updates. Search by VIN on the manufacturer site or nhtsa.gov.
  3. Visually inspect the wiring harness and connectors related to the exhaust gas temperature sensor 1/2 correlation bank 2 for damage, corrosion, chafing or poor contact.
  4. Measure reference voltage, ground and signal continuity at the component connector.
  5. Wiggle-test the harness while watching the signal in live data — dropouts reveal broken wires.
  6. Clear the code, complete a full drive cycle including the conditions from the freeze frame, and confirm P20E5 does not return.

How to fix P20E5

Start with the cheapest and most common causes before replacing expensive parts:

  • Repair wiring or connectors — $80–$250
  • Replace the faulty sensor or actuator — $150–$500
  • Control module repair — $300–$1,000

How much does it cost to fix P20E5?

Repair cost depends on which component actually failed. Typical scenarios for P20E5 (parts and labor, USD, independent shop rates):

  • Repair wiring or connectors: $80–$250
  • Replace the faulty sensor or actuator: $150–$500
  • Control module repair: $300–$1,000

Overall, fixing P20E5 usually costs between $80 and $1,000. An accurate diagnosis before buying parts saves money — the most expensive scenario is rarely the first one to check.

Can you drive with P20E5?

In most cases the car remains drivable, possibly with reduced performance or a disabled auxiliary system. If symptoms include stalling, no-start or brake/steering warnings, treat it as urgent.

Related OBD2 codes